Product: VRM-CC3-X

The VRM-CC3-X is a versatile 4HP/3U CompactPCI® CPU board, equipped with the Intel® series of ULV Celeron® or LV Pentium® III processors, designed especially for systems which require very low power consumption. Available either with 800/933MHz Low Voltage Pentium III or the 400/650MHz Ultra Low Voltage Celeron processor and up to 512MB RAM, the VRM-CC3-X covers a wide range of applications, including PXI systems. The DVI-I video interface is suitable for attachment of both, advanced (digital) and legacy (analog) displays (DSUB connector optionally). The VRM-CC3-X is provided with a 100Mbps Ethernet controller. The on-board CompactFlash socket allows for utilization of an ATA Flash card or IBM Microdrive®. A local expansion interface connector may be used to directly attach a companion I/O board, which can carry in addition a hard disk drive. As an option, rear I/O across the J2/P2 connector is available.

Features:

- Form Factor: CompactPCI Single Size CompactPCI style Eurocard (160x100mm²), front panel width 4HP (20.3mm)

- Processor: Designed for Intel® ULV Celeron® and LV Pentium® II Micro FC-BGA processors (Tualatin 0.13u generation), max. junction temperature 100ºC, processor thermal design power classification.
VRM-CC3-1: 400MHz ULV Celeron, 0.95V, 100MHz FSB, 256KB L2 cache, 3.4W typical
VRM-CC3-2: 650MHz ULV Celeron, 1.10V, 100MHz FSB, 256KB L2 cache, 7.0W typical
VRM-CC3-3: 800MHz ULV Pentium 3, 1.15V, 133MHz FSB, 512KB L2 cache, 11.2W typical
VRM-CC3-4: 933MHz LV Pentium 3, 1.15V, 133MHz FSB, 512KB L2 cache, 12.2W typical

- Chipset: Intel i815G chipset consisting of:
82815 Graphics/Memory Controller Hub (GMCH)
82801 I/O controller Hub (ICH2)
82802 Firmware Hub (FWH)
8761 LPC Super I/O

- Memory: 144-pin SO-DIMM socket. Support for up to 512MB, PC133, non ECC, unbuffered SDRAM. Support for serial presence detect (SPD) SO DIMM’s

- Video: Both analog monitor and digital flat-panel display support by DVI-I connectors (front panel), up to 1280x1024 pixel 16M colors 85Hz refresh rate, incorporates PanelLink Digital Technology (Silicon Image). Option: D-SUB (female HD15) connector available, replaces DVI-I connector.

- USB: Ports over-current protected, data transfer rate of up to 12Mbps, conforming to USB1.1
USB Port 1: Type A connector (front panel)
USB Port 2: J2/P2 Rear I/O Option

- Ethernet: 10/100Mbps Fast Ethernet controller, 82551ER chip, RJ45

- Serial Port COM1:
On-board RS-232E transceiver, RJ45 front panel connector (adapter RJ45 to D-Sub available), transceiver can be disabled if rear I/O COM port option is preferred. J2/P2 Rear I/O Option (TTL voltage level)

- Legacy I/O:
LPC Super-I/O interface connector, VRM-CC6 mezzanine companion board available for top (right) or bottom (left) mounting. J2/P2 Rear I/O option: Keyboard, Mouse, COM1 (TTL voltage level)

- IDE/ATA:
Ultra ATA/66 40-pin connector (primary IDE). CompactFlash socket for CFA ATA cards (secondary IDE). J2/P2 Rear I/O option: Primary IDE
CompactPCI: 32-bit, 33.3MHz, PCI bridge chip PLX 6150, 133MBps CPCI master
J2/P2 Rear I/O Option:
Primary IDE, USB Port 2, Keyboard/Mouse, COM1 (TTL Level), Rear I/O transition module VRM-CCY-RIO available

- PXI Support– TRIG0, TRIG1, TRIG6,TRIG7 (can be alternatively used as GPIO)

- BIOS: Phoenix BIOS with our embedded systems enhancements. 8Mbit Flash memory. Updates available upon request.

- Drivers (Major OS): Intel graphics drivers. Intel networking drivers

(more on datasheet)

- Power Requirements:
VRM-CC3-1: +5V+0.25V 1.3A max. +3.3V+0.1V 1.1A max
VRM-CC3-2: +5V+0.25V 1.9A max. +3.3V+0.1V 1.3A max.

Request a Quote for Ordering Info

Read the Datasheet