Product: VRM-CD2-X

The VRM-CD2-X is a high performance, low power 6U (double size Eurocard) CompactPCI® CPU board with the Intel® Pentium®M processor. The VRM-CD2-X is provided with an embedded graphics controller. The user can choose between a DVI-I receptacle, which allows for attachment of both, advanced (digital) and legacy (analog) flat panel displays and CRT monitors, or the classic VGA D-Sub connector. The Pentium®M (in particular the Low Voltage 1.4GHz chip) reduces the power consumption considerably compared to previous processor generations, thus enabling a reliable passive heatsink solution for thermal discharge. The VRM-CD2-X is equipped with several USB2.0 ports and four (4) independent Ethernet controllers for high speed networking up to 1000Mbps. The PICMG®2.16 Packet Switching Backplane is also supported (Dual Link Port). For mass storage attachment, the VRM-CD2-X provides both Ultra ATA/IDE and S-ATA interfaces.

Features:

Double size CompactPCI style Eurocard (160x233mm²), front panel width 4HP (20.3mm)
Designed for Intel®Pentium® M Micro FC-BGA 479 processors (0.13u Banias, 0.09u Dothan), maximum junction temperature 100°C
1.4GHz LV Pentium®M, (Dothan 733), 2MB L2 cache
1.8GHz Pentium®M (Dothan745), 2MB L2 cache
i855G (Brookdale) chipset consisting of:
82855GME Graphics/Memory Controller Hub (GMCH)- Montara
82801D I/O Controller Hub (ICH4)
82802 Firmware Hub (FWH) compatible
200-pin SO-DIMM socket (notebook style module), PC2100/2700 DDR266/333-SDRAM, 1GB maximum
Analog monitor and digital flat-panel display support by DV1-1 connector (front panel), up to 2048x1536 pixel 16M colors @ 75Hz refresh rate (analog), up to 1600x1200 pixel 16M colours @ 60Hz (digital), incorporates PanelLink Digital technology (Silicon Image). Front panel option: D-Sub (female HD15) VGA connector available, replaces the DVI-I connector
All ports over-current protected, data transfer rate of up to 480Mbps, conforming to USB2.0
USB port 1-2: Type A connector (front panel)
USB port 3: Expansion interface option (VRM-CCA mezzanine companion board)
USB port 4-5: J4/P4 Rear I/O option (VRM-CDY-RIO rear I/O transition module)
USB port 6: Dedicated to the optional on-board USB Flash drive
3 x 10/100/1000Mbps Gigabit Ethernet controllers, (82541), 1 x 10/100Mbps Fast Ethernet Controller (82562), 1 x Gigabit and Fast Ethernet accessible via RJ45 jacks from the front panel, 2 x Gigabit Ethernet as rear I/O according to PICMG®2.16 across J3 (alternatively accessible via RJ45 jacks from the VRM-CDY-RIO backpanel)
Ultra ATA/100 connector (secondary IDE), handover to VRM-CCA mezzanine expansion board with VRM-CCA on-board hard disk drive or
external device. Compact Flash socket (mezzanine module) for CFA ATA cards (Secondary IDE), J4/P4 Rear I/O option: Primary IDE accessible from VRM-CDY-RIO rear I/O transition module.
VRM-CD2 on-board hard disk drive module option (Primary IDE)
On-board dual Serial ATA controller, ports available across J5/P5 on VRM-CDY-RIO rear I/O module (alternatively accessible via Serial ATA connectors on board) RAID and non-RAID drivers
Optional on-board USB2.0 FLASH drive controller and 2 pcs. NAND FLASH up to 8Gbit each (total memory capacity up to 2Gbyte), can be configured as bootable disk, data transfer rates up to 18MB/s for read, 13MB/s for write (dual channel mode)
Optional usage of either: 1 slot for a PMC module, I/O from the front panel and across J5, On-board 2.5” hard disk module (primary IDE)
On-board LPC/USB/AC97 Super I/O, USB and audio expansion interface connector, suitable VRM-CCA 3U mezzanine companion board available
Rear I/O: 2 x Gigabit Ethernet (J3), 2 x Serial ATA (J3), Primary IDE (J4), 2 x USB (J4), LPT,COM,GPIO (J4), PMC mezzanine rear I/O (J5), Suitable rear I/O transition module VRM-CDY-RIO available

Request a Quote for Ordering Info

Read the Datasheet